[93capriceltz]

Here is a Harness:

http://ssconnectors.com/index.php?main_page=product_info&cPath=34_38&products_id=387

and

http://ssconnectors.com/index.php?main_page=product_info&cPath=34_38&products_id=388

now if we could talk him into doing one for a 91-93, that would be sweet!

 

[90coupedraggn]

OK so I have a question I am parting out a 96 Cadillac fleetwood and have removed all the HVAC equipment from it the question is can I install this unit as a whole and use the wiring harness adaptor sold else where and make this work or should I try to use all the OEM cadillac wiring if so can anyone supply the wiring schematic for the cadillac and Impala tbanks for any help you fellas can supply

 

[BigB9000]

Well, depends on what you mean by caddys wiring.

Can you remove the Instrument Panel harness and swap it out for your Impala's IP harness? No. The caddy does all kinds of different things than the Impala does.

Can you take a razor blade, and remove the E-tape from the caddy IP harness, then remove each and every wire that doesn't contain to the A/C system, then wire that into your car? Yes.

 

[90coupedraggn]

Yes sir thats what I ment was to remove all non-A/C WIRING but what about the adaptor harness as mentioned or some wiring schematics for both cars thanks

 

[BigB9000]

That adapter harness wont work for you, and you wont really need it, as you'll already most needed wiring.

You'll have to wire the A/C request, Interior lights, Power (both switches and constant) ground, etc...

 

[90coupedraggn]

well I have been a caddi fan fan for years so it was only fitting for me to this swap yes the roadmaster has its advantages but I love my caddies..... here is a short video.......



now to clean up the wiring and them map out all my impala wiring.......then the hard part removal of the dash and complete HVAC!!!!

 

[94MI9C1]

Looking good man. Interface wiring should be easy, you did the hard part of getting it all wired up. Bet you are going to find that you only need to hook up the entire setup to power and ground and you will be all set.

 

[9C1SSClone]

Looking good man. Interface wiring should be easy, you did the hard part of getting it all wired up. Bet you are going to find that you only need to hook up the entire setup to power and ground and you will be all set.

still havn't herd from Bigb9000 hope this wiring is coming.....

 

[sshuttlesworth24]

plug and play in effect yet? i bought the roady climate unit today and need to plug it up... unless any1 in the austin, tx / san antonio area can help for a fee? -___-

 

[eze415]

"7. blower control module, goes in place of the original blower resistor module mounted next to the blower in the duct."
where is this located? pieced together everything else off a roady except this.
thanks

 

[94MI9C1]

In the blower housing, to the left of the blower motor, you will see it, it is screwed into the housing with a few screws. See this pic

 

[eze415]

Mike,sir, you...

are the f**kin MAN!

wound up finally getting the time to do this swap and if it wasnt for the pictures i would have passed. Also a round of applause to member dabysan(also in this thread) because i totally flew by the post of the additional wires that are in the harness but not listed in one of the wiring diagrams for the 96 Climate control.
luckily i had grabbed several of each part from roadys that have come in to the yards because some of my parts took a dump on me. (gotta love having backups)

the only thing im stuck on and hopefully you can give me some insight is
-Lt Blue/Blk d15 Gnd for rear Window Defogger Relay.
are you taking off the relay looking thing from the manual unit and tying it in or is some other way being used?

thanks again Mike.

 

[94MI9C1]

If I remember right the RMS' s relay for defroster is down by the blower motor near the "A" pillar. Pretty sure I used this location as well and just extended the wires from the original relay on the original head to the new location

 

[2Tone]

Anyone have one of these for sale?

 

[eze415]

Anyone have one of these for sale?

i will in a few weeks. check pm

 

[94MI9C1]

I probably have a fair amount of components for the system that I could sell. Hit up via PM

 

[sshuttlesworth24]

Was the plug n play harness ever made. Ima take this on within the next week!

 

[eze415]

Was the plug n play harness ever made. Ima take this on within the next week!

even with the roady harness their is no plug and play you would still need to splice in about 10 wires to the impala/caprice harness. not that hard once you see where they are at. im tryin to get the last pictures for a writeup on this. hope to have it done in a week.

 

[bad25v8]

even with the roady harness their is no plug and play you would still need to splice in about 10 wires to the impala/caprice harness. not that hard once you see where they are at. im tryin to get the last pictures for a writeup on this. hope to have it done in a week.

Sweet some pictures and what wires go where will be sweet. Tackling mine soon too. Seats r out perfect time to tear apart dash too!!

Sent from AutoGuide.com Free App

 

[eze415]

Sweet some pictures and what wires go where will be sweet. Tackling mine soon too. Seats r out perfect time to tear apart dash too!!

Sent from AutoGuide.com Free App

Yeah its not as difficult as i thought it would be. As long as you have
The roady harness that cuts down finding out what plugs go where because
A few of the plugs are already linked up. just finishing Up the last pics and gonna get It into PDF